Knowledge Base

Topic

Smart Controllers.

153 articles

  1. WeatherTRAK Central Site Programming Worksheet - Legacy The WeatherTRAK central site programming worksheet was initially sent out with controllers so that maintainers could record station information and Specific Programming Documents
  2. WaterCompass for ET PRO 3 You should buy a water compass! Click here:  Click Me! Upgrade Your Controller
  3. Programming a Station If it is a new irrigation system installation or maintenance visit, programming a Station with WeatherTRAK Mobile can be a Specific Programming Documents
  4. WeatherTRAK Controller Spring Start-Up Update Table of Contents Step 1 - Before you go! Make sure you have WeatherTRAK accessStep 2 - Arrive on Getting Started
  5. How to Wire a Pump Start Decoder Delete Note If the pump start decoder is not pre-programmed you will need to program it at the controller BEFORE Installing Decoders
  6. Programming the WeatherTRAK ET Pro2 in Automated by WeatherTRAK Mode Update Table of Contents Assigning a Station to a ProgramSelecting Usage of the Water WindowConfiguring Usable Rainfall for Specific StationsSelecting ET Pro2: Programming
  7. Manual Operation at the Controller Panel Manual operation can be initiated from the OptiFlow controller panel. You will need to unlock the controller, placing it into Programming
  8. Unlocking an Offline OptiFlow Controller This article will discuss how to unlock an offline OptiFlow controller with an unlock code retrieved using WeatherTRAK Central. You Troubleshooting
  9. Receiving a Promotional Code and Upgrading Your Controller - EXPIRED These instructions will assist you in receiving a promotional code for a discount when you upgrade to a Rachio controller. Legacy: ET Pro2, ET plus
  10. Best Practices for Pausing Irrigation on WeatherTRAK Controllers Pausing irrigation on WeatherTRAK controllers for events Event Pause HydroPoint recommends using the WeatherTRAK Event Pause feature to pause controllers Controller Troubleshooting
  11. Setting the Maximum Active Stations Setting the Maximum Active Station number enables your stations to be programmed. The number you select should correspond to the Specific Programming Documents
  12. WT SIM Card Swap Instructions This guide is to provide directions for how to replace the SIM card in your controller with a new SIM Installs & Replacements Guide
  13. Grounding the WeatherTRAK 2-Wire Controller Update Table of Contents Using the Line Surge Arrestor Diagram of valve box and wiring For protection from electrical surges, Installing Decoders
  14. Troubleshooting Blown or Popping Fuses Update Table of Contents Step 1 - Inspect the Controller for DamageStep 2 - Disconnect Power and Station WiresStep 3 Controller Troubleshooting
  15. Why is my Display Screen Blank? ET Plus If your WeatherTRAK ET plus display screen is blank, you can go through the following steps to make the display ET Plus: Troubleshooting
  16. WeatherTRAK LC+ Documents Product Catalog WeatherTRAK Product Catalog Technical Specifications WeatherTRAK LC+ Tech Sheet Installation Instructions WeatherTRAK LC+ Installation Guide Supporting Documents WeatherTRAK Documents
  17. Differences with Associating Users with Account, Site, or Controller For Account Administrators that have Admin access in WeatherTRAK Central. Otherwise, contact support to discuss changing associations to an account. Account Setup
  18. Spring Is Upon Us! Please reference the following Technical Resources list below which includes your Spring Startup checklist which will help you in preparing Popular Articles
  19. Why Aren't My Stations Coming On? Update Table of Contents Turn the Main knob to RUNDoes RAIN SWITCH display while in the RUN position?The Controller ET Pro2: Troubleshooting
  20. Upgrading ET Pro3 / OptiFlow XR H2O Controllers to Support 200 Stations To upgrade an ET Pro3 or OptiFlow XR H2O controller to support 200 stations, you will need to order the Installation
  21. Programming a Single Valve H2O 2-Wire Decoder These instructions are for H2O 2-Wire controllers running firmware version 8.9 (released August 2021) and higher. To find your Programming Decoders
  22. Programming a Two Valve H2O 2-Wire Decoder These instructions are for H2O 2-Wire controllers running firmware version 8.9 (released August 2021) and higher.  To find your Programming Decoders
  23. Programming a Master Valve H2O 2-Wire Decoder These instructions are for H2O 2-Wire controllers running firmware version 8.9 (released August 2021) and higher.  To find your Programming Decoders
  24. Programming a Flow Sensor H2O 2-Wire Decoder These instructions are for H2O 2-Wire controllers running firmware version 8.9 (released August 2021) and higher. To find your Programming Decoders