Knowledge Base
/

Topic

Programming.

  1. Baseline 3g migration playbook (WFWW) (Legacy) Baseline 3G Playbook This document is to summarize content and communications for the Baseline 3G Modem end of life, and Programming
  2. Bypassing the Activation PIN process Adding a controller to BaseManager This article explains how we can bypass the activation PIN process for Baseline controllers that Programming
  3. Control Point & Dynamic Flow Allocation Groups There are two different, but very similar, features for turning on the smallest available control points. Control Point Groups can Programming
  4. Controller Memory Low Message Controller Memory Low Message NOTE: The newer 3200S display should not have this issue based on how its manufactured. Controller Programming
  5. Downgrade/Update Firmware via USB Delete Circumstantial Situations Only Please Consult with Tier 2 or Tier 3 before doing this PLEASE CONSULT BEFORE DOWNGRADING FROM Programming
  6. Flow Set-Up with a Single Water Source Learn how to configure flow on the BaseStation 3200 via BaseManager. Steps include devices, water sources, control points, and mainlines. Programming
  7. How to change the IOT URL for a 3200S *This can only be used for Tier 2. Please reach out to Tier 2 with the Company/ Site/ Controller information. Programming
  8. IrrApp2.exe Error Troubleshooting When a Baseline controller presents the following error. Use this guide to resolve the issue. * First, as we should always Programming
  9. Irrigation Controller Shortcuts When you are configuring the settings on a BaseStation irrigation controller, you need to navigate through many screens and press Programming
  10. Mac address location instructions How to find the MAC Address at the 3200S * Go to Network then to Communication Setup * Communication Type Ethernet will Programming
  11. Manage by Flow What is Manage by Flow? Manage by flow is a feature in BaseManager that optimizes the number of stations that Programming
  12. Preparing a 3200 Programming Backup from BaseManager 1.   From the home page in BaseManager, select Administration. The Administration page displays.  2.  From the Administration page, select Administration. Programming
  13. Preparing a Program Backup for a BL-1000 & FlowStation Preparing Program Backup for the BaseStation 1000 and a FlowStation   Important: ·        Create a folder in your documents folder and name Programming
  14. Process; Requesting Data >3 Years Old BaseManager historical data older than 3 years is archived externally and no longer accessible to customers. If a customer requests Programming
  15. Programming a Zone Event Stop/Pause Note: Compatible with 3200S, firmware versions 19.9 and up.  Accessing Zone Event Dates 1. Turn the 3200S dial to Programming
  16. Quick Start Guide Update Table of Contents IntroductionSmart Watering ModesSoil Moisture Sensor-Based WateringWeather-Based WateringController Front Panel LayoutOn-Screen HelpZone Status ReportUnderstanding Zone StatusesStep 1 Programming
  17. Setting Up Water Source Priorities With Baseline’s BaseStation 3200 irrigation controller, you can use water from multiple sources to run your irrigation programs. When Programming
  18. Shutting Down Irrigation Based on a Water Source Empty Condition Update Table of Contents Step 1 - Installing the Monitoring Device in the ReservoirUsing an Event biCoder and Float Switch Programming
  19. Stopping Irrigation at a Specific Temperature Reading You can set up your Baseline 1000 irrigation controller to stop all irrigation when the temperature drops below a specific Programming
  20. Stopping Irrigation for Rain Events If an irrigation system that you manage is running during a rain storm, your customer might be criticized for wasting Programming
  21. Stopping Irrigation for Rain Events If an irrigation system that you manage is running during a rain storm, your customer might be criticized for wasting Programming
  22. SubStation Quick Start Guides See the attached documents below when referencing the Quick Start Guides for the various models of SubStation depending on the Programming
  23. Turning Electricity On/Off with a Program Update Table of Contents Required MaterialsOverview of the StepsStep 1 - Installing the Dayton RelayStep 2 - Installing the biCoderStep Programming
  24. Turning Electricity On/Off with a Program (BaseStation 1000) With the correct materials, you can set up your Baseline irrigation controller to have a connected 110V electrical circuit turn Programming
  25. Updating the Firmware from a USB Drive Important We always recommend that you perform a system backup before you update the SubStation firmware. If you experience issues Programming
  26. Updating the Firmware from a USB Drive Update Table of Contents Copy the Firmware Update from the Baseline Website onto a USB DriveUpdate the Firmware on the Programming
  27. Updating the Firmware from a USB Drive(FlowStation) Important We always recommend that you perform a system backup before you update the FlowStation firmware. If you experience issues Programming
  28. Updating to the V17 Firmware from a USB Drive Update Table of Contents Copy the Firmware Update from the Baseline Website onto a USB DriveUpdate the Firmware on the Programming
  29. Verifying Cloudgate AT&T DNS Summary As of 9/30/2025 there is an initiative to update Cloudgate cell modem configurations to no longer use Programming
← All Baseline topics